3010 Pintle Hitch - Tub Grinder - Overview
3010 Pintle Hitch Tub Grinder General Specifications
  Weight w/ Pintle Hitch 35,840 lbs. (16,256.75 kg)
  Transport Width 8 ft. 6 in. (2.54 m)
  Transport Height 11 ft. (3.35 m)
  Transport Height w/ Tub Cover 135.82 in. (345.01 cm)
  Transport Length w/ Pintle Hitch 38 ft. 4 in. (11.68 m)
  Axle (2) - 22,500 lbs. (10,205.82 kg)
  Electrical 24 volt machine
  Tires 255/70R X 22.5
  Engine: 475 hp (354.21 kW) CAT C15
540 hp (402.68 kW) CAT C15
  Fuel Capacity 180 Gallons (681.37 Liters)
  Hydraulic Oil Capacity 50 Gallons (189.3 Liters)
  Lights Clearance, Directional
  Tub Width 10 ft. (3.04 m)
  Depth 46 in. (116.84 cm)
  Tub Diameter at Base 8 ft. (2.43 m)
  Tub Wall 1/4 in. (.635 cm) Thick
  Tub Floor 3/8 in. (.953 cm) Thick
  Tub Drive 120H Chain, Single Drive Hydraulic Motor
  Service Access 90° Tilting Tub
  Tub Speed Sensor Electronic Self Governing
  Stacking Conveyor 26 ft. (7.92 m) Long x 30 in. (76.2 cm) Wide
  Belly Conveyor 30 in. (76.2 cm) Wide Impact Resistant
  Hammers 20 Fixed Single Bolt or 40 Swinging
  Rotor - Shaft Diameter 6 in. (15.24 cm) Stress Proof Steel
  Rotor Length 44 in. (111.76 cm)
  Rotor Plates 16 in. (40.64 cm) Diameter x 1-1/2 in. (3.81 cm) Thick
  Feed Opening 45 in. x 25 in. (114.3 cm x 63.5 cm)
  Screen Area 2,403 Square Inches (15,503.19 sq. cm.)
  Hammer Rods (8) - 1-1/2 in. (3.81cm) Diameter
  Bearings 4 in. (10.16 cm) Oil Bath Bearing
  Hammermill Drive Direct Drive through HPTO Oil Cooled Clutch
3010 Pintle Hitch Tub Grinder Options
Hammer Options: (Must choose one)
  (38) 3/4" x 3" Swing Hammers
(38) 1" x 3" "Supreme" Swing Hammers
(20) Fixed Hammers
Screen Options: (Must choose one)
  Screen 1" Hole 1/2" Thick Hardox w/ Doubler
Screen 1 1/2" Hole 1/2" Thick Hardox w/ Doubler
Screen 2" Hole 1" Thick
Screen 3" Hole 1" Thick
Screen 4" Hole 1" Thick
Screen 4 3/4" x 7" Hole 1" Thick
Screen 6" x 9" Hole 1" Thick
Discharge Conveyor Drive Roller: (Must choose one)
  Top Drive Roller
Magnetic Roller Complete w/ Aluminum Deflector Chute
Remote Control Option: (Must choose one)
  No Remote Control
6 Function Tub: Start, Stop, Rev Cnvyr: Up, Down Eng: Kill
6 Function plus Cover: Raise, Lower
Mill Cover
12 hp Compressor w/ Vandal protection, 50' of 1/2" hose with reel (5th Wheel Only)
3/4" Air Impact w/ Two Sockets & Extension
Lockable Steel Toolbox
Hydraulic Front Stabilizer Jacks
12' Tub Flare Extension (unavailable w/tub cover)
Tub Agitator Kit
Hammer Rod Puller
Tub Cover
  An operational characteristic of all grinders is that objects may be thrown out of the tub. Tub Covers reduce the risk of potential injury or property damage from thrown objects. Proper use of the Tub Cover provides the operator with a means to help control the area over which thrown objects may fall. Combined with a decrease in the percentage of objects thrown from the tub, the Tub Cover is an effective means of reducing risk to personnel and property.
DuraTech Industries International, Inc. reserves the right to change its products or their specifications at any time without notice or obligation. Illustrations, specifications, and descriptions contained herein were accurate at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories, and may not include all standard equipment.