9564 - Horizontal Grinder - Overview
9564 Horizontal Grinder General Specifications
  Spacing 57-1/2 in. (1.46 m)
  5th Wheel Weight 33,750 lbs. (15,308.74 kg)
  Total Axle Weight 57,750 lbs. (26,195 kg)
  Total Weight 91,500 lbs. (41,503.7 kg)
  Transport Width 11 ft. 10 in. (2.59 m)
  Transport Height 13 ft. 5 in. (4.09 m)
  Transport Length 53 ft. (15.18 m)
  Engine Caterpillar C-27 1050 HP (782.9 kW) Diesel Engine
  Clutch HPTO 15 TD Wet Clutch
  Fuel Capacity 380 Gallons (1,440 L)
  Fuel Consumption 45.7 gal./hr. (179.8 L/hr)
  Hydraulic Oil Capacity 145 Gallons (548.9 L)
  Rotor Drive 10 Groove 8V
  Hopper Capacity 315 Cubic Ft. (8.91 cu. m)
  Hopper Width 61-1/2 in. (156.2 cm) Bottom, 74 in. (187.7 cm) Top
  Hopper Length: 248 in. (629.9 cm) Door Up
300 in. (762 cm) Door Down
  Hopper Depth 35 in. (88.9 cm)
  Feed Opening 61-1/2 in. X 40 in. (156.2 cm x 106.6 cm)
  Feed Height 96 in. (234.8 cm)
  Electric (PLC) Programmable Logic Controller
  Hydraulic Drives Two Load Sensing Pumps
  The PLC (Programmable Logic Controller) regulates feed rate based on rotor speed. Feed rate is proportional to rotor speed. Maximum feed rate is adjustable. Hammermill weight consists of shaft, hammer rods, bits, hardware, and tool holders.
  Rotor Shaft Size 5-7/16 in. (13.81 cm)
  Rotor Width 64 in. (162.6 cm)
  Rotor Speed 1,125 RPM
  Tip Swing Diameter 50-3/4 in. (126.9 cm)
  Number of Tips 24
  Cylinder Mid Plates 1-1/2 in. (3.81 cm) Thick x 39 in. (99.06 cm) Diameter
  Cylinder End Plates 1-1/2 in. (3.81 cm) Thick. x 40 in. (101.06 cm) Diameter T-1 Material
  Weight 12,100 lbs. (5488.47 kg)
  Hammer Rod Size 3-1/4 in. (8.26 cm)
  Rotor Diameter 42 in. (106.9 cm)
  Drive Dual Orbit Motor / Double Reduction Gearboxes
  Screen Area 4,340 sq. in. (27,99.944 sq. cm)
  Thickness 1 in. (2.54 cm)
  Hole Sizes Available in a variety of sizes
  Length 28-1/2 ft. (8.69 m)
  Width 54 in. (137.2 cm)
  Length 30.5 ft. (9.3 m)
  Width 48 in. (121.9 cm)
  Oscillating 40 Degree side-to-side
  Stacking Height 22' (6.71 m) @ 30 Degree Incline
  Air Compressor Available
  Magnetic Roller Available
9564 Horizontal Grinder Options
Magnetic Discharge Roller:
  Magnetic roller on top drive roller and aluminum discharge slide
Remote Control
  19 function remote control allows the operator to have complete control of the grinder while operating support equipment.
Engine Powered Air Compressor with Hose Reel and Air Hose
DuraTech Industries International, Inc. reserves the right to change its products or their specifications at any time without notice or obligation. Illustrations, specifications, and descriptions contained herein were accurate at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories, and may not include all standard equipment.