5064 - Horizontal Grinder - Overview
5064 Horizontal Grinder General Specifications
  Axels (3) - 22,500 lbs. (9,979.03 kg)
  Spacing 49 in. (1.24 m)
  5th Wheel Weight 21,880 lbs. (9,924.6 kg)
  Total Axle Weight 48,680 lbs. (22,080.9 kg)
  Total Weight 70,560 lbs. (32,005.5 kg)
  Transport Width 8 ft. 4 in. (2.54 m)
  Transport Height 13 ft. 1 in. (3.99 m)
  Transport Length 39 ft. 5 in. (12.01 m)
  Engine: Caterpillar C-18 630 HP (470 kw) Diesel Engine
Caterpillar C-15 540 HP (403 kw) Diesel Engine
Caterpillar C-15 475 HP (354 kw) Diesel Engine
  Clutch HPTO 14 TD Wet Clutch
  Fuel Capacity 300 Gallons (1,135 L)
  Hydraulic Oil Capacity 145 Gallons (548.9 L)
  Rotor Drive 4 Groove Belt
  Hopper Capacity 197 Cubic Ft. (5.59 cu. m)
  Hopper Width 61-1/2 in. (156.2 cm) Bottom, 74 in. (187.7 cm) Top
  Hopper Length: 13 ft. 2 in. (4.01 m)
  Hopper Depth 35 in. (88.9 cm)
  Feed Opening 61-1/2 in. X 40 in. (156.2 cm x 106.6 cm)
  Feed Height 96 in. (234.8 cm)
  Feed Roller 36 in. (91.44 cm) dia.
  Load Speed Sensor Programmable Logic Controller
  The PLC (Programmable Logic Controller) regulates feed rate based on rotor speed. Feed rate is proportional to rotor speed. Maximum feed rate is adjustable. Hammermill weight consists of shaft, hammer rods, bits, hardware, and tool holders.
  Weight 8,550 lbs. (3,878 kg)
  Rotor Bearing Diameter 4-7/16 in. (11.27 cm)
  Rotor Shaft 7 in (17.78 cm) Alloy Steel
  Rotor Width 64 in. (162.6 cm)
  Rotor Plates 32-1/4 in. (81.92 cm) dia. X 1-1/2 in. (3.81 cm) Thick
  Tip Swing Diameter 41 in. (104.14 cm)
  Number of Hammers 32 Single Bolt
  Hammer Rods (16) - 2 in. (5.08 cm) dia.
  Screen Area 3,705 sq. in. (2.39 sq. m)
  Hole Sizes Available in a variety of sizes
  Length 22 ft. (6.71 m)
  Width 54 in. (137.2 cm)
  Length 26 ft. (7.75 m)
  Width 48 in. (121.9 cm)
  Oscillating 40 Degree side-to-side
  Electrical 24V
  Lights Clearance, Directional
  Tires (6) - 445/50R22.5 super single
  Hydraulic Jacks Trailer Standard Equipment
  Air Compressor Available
  Magnetic Roller Available
  CAT Track System Available
5064 Horizontal Grinder Options
Magnetic Discharge Roller:
  Magnetic roller on top drive roller and aluminum discharge slide
Remote Control
  19 function remote control allows the operator to have complete control of the grinder while operating support equipment.
CAT Track System
DuraTech Industries International, Inc. reserves the right to change its products or their specifications at any time without notice or obligation. Illustrations, specifications, and descriptions contained herein were accurate at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories, and may not include all standard equipment.